Difference between revisions of "Light-emitting diode"
| Line 40: | Line 40: | ||
* "Build Your Own Light Pipe" [http://labs.ideo.com/2015/07/28/build-your-own-light-pipe/] | * "Build Your Own Light Pipe" [http://labs.ideo.com/2015/07/28/build-your-own-light-pipe/] | ||
* "3D printed light pipes" [http://www.disneyresearch.com/project/printed-optics/] | * "3D printed light pipes" [http://www.disneyresearch.com/project/printed-optics/] | ||
| − | * "Care222 LED Lamp " [http://www.faruvclite. | + | * "Care222 LED Lamp " [http://www.faruvclite.com/] |
* "3D Printing Light Pipes" [https://www.fictiv.com/resources/starter/prototyping-with-light-pipes] | * "3D Printing Light Pipes" [https://www.fictiv.com/resources/starter/prototyping-with-light-pipes] | ||
* "Using t-glase for Light-Pipes" [http://taulman3d.com/t-glase-features.html] | * "Using t-glase for Light-Pipes" [http://taulman3d.com/t-glase-features.html] | ||
Latest revision as of 23:11, 18 May 2022
A light emitting diode is the most popular kind of optoelectronics.
To make the LED light up, you need a power supply (any voltage) and a resistor.
The resistance required is as follows: R = (U_power - U_led) / I_max
Example: a LED with voltage drop of Uled=1.2V and a max current of I_max=0,020A (20mA) to be powered by a 5V DC source needs:
R = (5-1.2)/.02 = 190 ohm
You then connect a 190 ohm resistance in series with the LED to make it work.
Contents
POV[edit]
throwies[edit]
Several other wiki discuss how to turn LEDs into "throwies"(little blinking LED devices that attach to outdoor structures via magnets):
- Cybords wiki: Throwie Talkie: A Talkie is a Throwie that has been hacked to blink graffiti messages in Morse code.
- TagRecord.com Wiki: Led throwies
- the mayowiki: Throwies
sensor[edit]
A few people use LEDs in an unusual way: as sensors.
light pipe[edit]
Many people want and blinking/glowing spot *here*, controlled by a nearby circuit board *there*. One approach is to put a LED directly on the circuit board *there*, and guide the light from that LED to *here* using a light pipe.
Some commercial off-the-shelf light pipes; and some tips on building custom light pipes from transparent acrylic, aluminum foil, or 3D printed materials:
- "LED light pipes" [1]
- "LED light pipes" [2]
- "Build Your Own Light Pipe" [3]
- "3D printed light pipes" [4]
- "Care222 LED Lamp " [5]
- "3D Printing Light Pipes" [6]
- "Using t-glase for Light-Pipes" [7]
- "Light Guide Techniques" [8]
- "Optical light pipes" [9]
- "Light Pipe Selector Guide" [10]
- "LED light pipes" [11]
5.0v - 3.3V voltage drop via red LED[edit]
The average red LED has a 1.7V voltage drop. This property can be (ab)used to power very small 3.3V IC's from a 5.0V power supply -- put the LED in series with the 5V line. There probably won't be enough power used to light the LED properly, but this does not matter for the voltage drop property.
further reading[edit]
LEDs used normally: to emit light:
http://en.wikipedia.org/wiki/LED
LEDs used "in reverse": as light sensors:
