Difference between revisions of "Programming the Device"
Jump to navigation
Jump to search
(→Loading Firmware: add pic) |
|||
Line 63: | Line 63: | ||
==Loading Firmware== | ==Loading Firmware== | ||
*Download [[dsPic_Programmer.zip]] | *Download [[dsPic_Programmer.zip]] | ||
− | + | *Save to a directory. | |
− | + | ::e.g. desktop | |
− | *Unzip the dsPic_Programmer.zip, then you have unziped file. | + | *Unzip the dsPic_Programmer.zip, then you have an unziped file. |
− | [[Image: | + | [[Image:prog_guid_dl.JPG]] |
− | * | + | |
+ | ---- | ||
+ | |||
+ | *Drag the unzip file to a director. | ||
::eg. USB memory devics | ::eg. USB memory devics | ||
− | [[Image: | + | [[Image:prog_guid_drag.JPG]] |
− | *Save your .hex file(foo.hex) to your directory location e.g. | + | |
− | + | ---- | |
− | + | ||
+ | *Save your .hex file(foo.hex) to your directory location | ||
+ | ::e.g. X:\dsPic_Programmer\ ---> X:\ is the driver where the dsPic_Programmer located | ||
+ | [[Image:prog_guid_hex.JPG]] | ||
===Download Firmware=== | ===Download Firmware=== | ||
*Start a Command Prompt | *Start a Command Prompt | ||
Line 80: | Line 86: | ||
**Make sure your device is connected through a "Direct RS232 Cable" to PC Serial Port. | **Make sure your device is connected through a "Direct RS232 Cable" to PC Serial Port. | ||
**Change to the directory where dsPicProgrammer.jar is located and run the command: | **Change to the directory where dsPicProgrammer.jar is located and run the command: | ||
− | + | ***for example, jre\bin\java -Djava.library.path=.\rxtx\bin -jar dspicProgrammer.jar COM1 115200 foo.hex | |
− | |||
***Or directly using dsPicProgrammer.bat COM1 115200 foo.hex(Windows) | ***Or directly using dsPicProgrammer.bat COM1 115200 foo.hex(Windows) | ||
***java -jar dsPicProgrammer.jar /dev/ttyS0 115200 foo.hex (Linux) | ***java -jar dsPicProgrammer.jar /dev/ttyS0 115200 foo.hex (Linux) |
Revision as of 19:08, 19 October 2008
Contents
Requirements
Hardware
- PC with COM port (Windows XP Installed for MPLAB)
- ICD2 Programmer
- Target Board
- 5V Power Supply
Software
- MPLAB IDE v7.50: v7.60 is not compatible with our current ICD2 Programmers. There are consistent "Devices cannot be founded" warnings.
- dsPicProgrammer (dsPicProgrammer.jar)
Files
- dsPicBootloader (bl_5011.hex). Original assembly code by ingenia can be downloaded from here.
- Application hex file (e.g. app.hex)
Loading Bootloader (Once only)
Step | Remarks |
---|---|
Install MPLAB IDE |
|
Install USB Driver |
|
Select Target Chip |
|
Target <-> ICD 2 |
|
ICD 2 <-> PC |
|
Load Bootloader |
|
Start Programming |
|
Finishing |
|
Loading Firmware
- Download dsPic_Programmer.zip
- Save to a directory.
- e.g. desktop
- Unzip the dsPic_Programmer.zip, then you have an unziped file.
- Drag the unzip file to a director.
- eg. USB memory devics
- Save your .hex file(foo.hex) to your directory location
- e.g. X:\dsPic_Programmer\ ---> X:\ is the driver where the dsPic_Programmer located
Download Firmware
- Start a Command Prompt
- Start -> Run
File:2 1 run.JPG - Enter cmd
File:2 2 cmd.JPG
- Start -> Run
- Run dsPicProgrammer
- Make sure your device is connected through a "Direct RS232 Cable" to PC Serial Port.
- Change to the directory where dsPicProgrammer.jar is located and run the command:
- for example, jre\bin\java -Djava.library.path=.\rxtx\bin -jar dspicProgrammer.jar COM1 115200 foo.hex
- Or directly using dsPicProgrammer.bat COM1 115200 foo.hex(Windows)
- java -jar dsPicProgrammer.jar /dev/ttyS0 115200 foo.hex (Linux)
- where COM1 is your COM Port ID
- 115200 is communication speed [in bps]
- foo.hex is your firmware new file
- When the program prompt you for an input, press y:
File:2 4 prompt.JPG - If communication can be established, you should see something like this:
- Wait until programming is completed.
- after all completed, power OFF your device, then power ON again, enjoy your new updated.
Troubleshooting
Invalid COM Port
- In case of selecting an invalid COM port, you should see the error message:
gnu.io.NoSuchPortException: Choosing COM Port Error
Missing firmware file
- In case of selecting a firmware file that does not exist, you should see the error message:
java.io.FileNotFoundException: foo1.hex <The system cannot find the file specified>